24V 680RPM 887kgfcm AmpFlow DC Motor with Speed Reducer

Availability: Discontinued

Buy locally from a partner

Country:
Description

Yup, now we carry the famous AmpFlow heavy-duty, low-cost motor with gearhead as speed reducer. This is the famous motor for heavy duty combat robot.

This speed reducer uses a unique three-stage chain-and-sprocket mechanism that reduces cost while still maintaining high torque capacity.

This unit provides speed reduction and torque multiplication, and it's an easy way to "bolt-in" the AmpFlow motors.

The speed reducers are made with a three-piece aluminum case that has been precision CNC machined. A total of six sprockets, three roller chains, and five bearings comprise the mechanism. The long output shaft makes it easy to mount pulleys, sprockets, gears, or wheels in the required position. Care was taken to make this unit as compact as possible. The overall dimensions are 6 inches x 3 inches x 2 inches. But the motor is recessed slightly into the reducer, so the net length added to the motor is only 1.78 inches.

The speed reducer uses a unique arrangement of roller chains. This results in torque and efficiency comparable to gear-type reducers at just 1/2 or even 1/3 of the cost of high-torque, geared speed reducers. There is slightly more noise, but these units are ideal when silent operation is not required.

The hardened output shaft is 3/4-inch diameter and 2.2 inches long. It has a 1/4-inch keyway and a 5/16-24 tapped hole. It is fixed to the sprocket with a hexagonal spline to strengthen the connection between the shaft and sprocket.

A single stage of roller chain reduction is generally considered to be about 98% efficient. Add in some friction from the five bearings and we are at about 90% efficiency.

Warranty Period: 12 months
Features

Specifications:

  • Peak Horsepower: 2.1
  • Motor Diameter: 3.1 inch
  • Motor no load curent: 3.1Amps
  • Motor stall current: 266 Amps
  • Reduction Ratio: 8.3:1
  • Peak Torque: 770 in-bls or 87 Nm
  • Nominal Voltage: 24V
  • No-load RPM: 680
  • Weight: 4.3kg
  • Compatible motor driver:
 
Specifications
Motor Specification
Voltage24VDC
Speed (RPM)501 - 1000
Torque (kgf.cm)> 100.01kgf.cm
Current<266A
EncoderNo
Packing List
  • Motor with gear attached as shown
Resources

How to choose a suitable motor

Torque Testing
 

This picture shows the speed reducer undergoing a torque capacity test. The motor is locked and unable to turn. Weight is loaded onto the end of the 40-inch bar until the speed reducer fails. The failure point is 3500 inch-pounds. The failure point is the chain on the last stage of speed reduction. The gearbox suffered no other damage. The $10 chain was replaced and it's as good as new.
 
Backlach Test

The gearhead is tested for backlash by locking the motor in place. A load of 200 ounce-inches is applied in both clockwise and counter clockwise directions. The total deflection is +/- 1.2 degrees. This figure may increase somewhat with higher loads and chain wear, but replacement chains are available.
 
Mounting

Four long 1/4"-20 bolts go all the way through the width of the reducer. The four mounting bolts are supplied with the the unit. They are sufficient in length to mount the gear motor to a 3/8-inch thick panel. If the panel is thicker, longer bolts will be needed. Do not operate the speed reducer with bolts that are missing or too short - they are required for structural integrity.
Q & A (2)

Ask a question

Reviews
  • 5 out of 5
                  
  • 5
    100%
  • 4
    0%
  • 3
    0%
  • 2
    0%
  • 1
    0%
Sort By: