4 Layers Cluster Case with Fan for RPi & Jetson Nano

Note: From 29th Mar 2021 onwards, heatsink sets are NOT included in the packing list.

Are you looking for a cooling solution for your Raspberry Pi 4B/Jetson Nano Clusters with a nice design and dazzling at the same time?

We bring to you this 4 Layers Cluster Case! We performed a thermal stress test with Raspberry Pi 4 Model B 2GB together with this 4 Layers Cluster Case and it stays cool even if the RPi4B is overclocked to 2.1GHz. Amazing heat dissipation.

Rack Tower stands for a new concept for the 4-layer acrylic case cluster.

This 4-layer acrylic oversized fan enclosure is a new product designed to provide shell protection and cooling solutions for Raspberry Pi clusters, Raspberry Pi NAS servers, Jetson Nano clusters, and disk array clusters. It is very delicate. The long fixing screws are designed with flat head screws, smooth and easy to install. The fool-proof design of the positioning holes also can prevent you from having trouble during installation. A variety of screws with different specifications can meet your various product fixing needs. For example, Raspberry Pi, 2.5-inch solid state drive, Jetson Nano, and so on.

In addition, the large fan is driven by 5V, which can be directly powered by the Raspberry Pi, and it will have a colorful halo when it is running, which is very cool.

How to assemble Raspberry Pi on cluster case:

1. Fix the copper sticks to the acrylic layer after peeling off the protection film.

2. Paste heat sinks to Raspberry Pi and fix the raspberry pi to the acrylic layer with M2.5 nuts.

Note: The Raspberry Pi boards and heatsinks are NOT included in the package. If you need them, please get them separately. 
 

3. Fix the bracket holder to the fan with long steel screws and nuts.

4. Fix other devices as mentioned before, for example, 4 pieces of Raspberry Pi or other combinations. And then place them as in the following picture. Pay attention to the direction where there is an “R” mark. Connect the fan cable to Raspberry Pi on 5V and GND Pin.

Note: Please beware of the direction of the acrylic holder.

Note: Incorrect polarity may cause damage to your device.

6. Place another piece of acrylic layer on the top and fixed it with long steel screws.

7. Install acrylic crystal hander with M3x9mm screws.

Check out this assembly tutorial from 52Pi:

Popular application:

• Raspberry Pi smart NAS cluster

Note: The Raspberry Pi boards, heatsinks, 2.5" SSD and USB 3.0 to SATA III SSD Adapter are NOT included in the packing list.
 

• Jetson Nano AI Deep Learning (Machine Learning) Cluster storage

Note: The Jetson Nano board, 2.5" SSD, and USB 3.0 to SATA III SSD Adapter are NOT included in the packing list
 

• Compatible with Raspberry Pi boards:
  • Raspberry Pi 5
  • Raspberry Pi 4B 8GB
  • Raspberry Pi 4B 4GB
  • Raspberry Pi 4B 2GB
  • Raspberry Pi 4B 1GB
  • Raspberry Pi 3B+
  • Raspberry Pi 3B
  • Raspberry Pi 3A+
• Compatible with Jetson Nano as well:
  • NVIDIA Jetson Nano Dev Kit Rev.B01
  • NVIDIA Jetson Nano 2GB Dev Kit
• Easy to assemble
  • The long fixing screws are designed with flat head screws, smooth and easy to install. The fool-proof design of the positioning holes can prevent you from having trouble during installation. A variety of screws with different specifications can meet your various product fixing needs.
• Extreme heat dissipation effect
  • With 120mm 5V RGB LED fan for better heat dissipation. The new fan allows switching by separating the motor from the LED (Two of the four wires are the cable of the fan, and the others are the LED power supply cables.). This case is open on three sides with each acrylic layer containing enough space for maximum airflow for each Raspberry Pi.
• Easy access to all I/O ports
  • With SD card converters, it's easy to remove the SD cards. Users can access all ports of the Raspberry Pi and Jetson Nano boards, such as GPIO ports, HDMI ports, USB ports, SD card slots, and so on.
• Colorful LED 120mm fan
• With a crystal handle, easy to carry on
• Flexible mounting position
• Dimension after assembled: 15cm x 17cm x 13.5cm (LxHxW)

Note: If you want to make better use of space, you can place the Raspberry Pi on one side of the bracket, and on the right side, you can place other small equipment, such as UPS power, etc., and it can also be used as a place for cables.

Packing list:

• 1 x Acrylic case set
  • 1 x Right baffle
  • 1 x Left baffle
  • 4 x Middle interlayer
  • 2 x Fan bracket
  • 1 x 125mm Acrylic cylinder
• 4 x 130mm male and female rivet
• 2 x M3x8mm screw (for handle)
• 1 x 120mm RGB LED 5V fan
• 4 x M3x30mm screw (for 120mm fan)
• 4 x M3 nut (for 120mm fan)
• 17 x M2.5x5+6mm copper column (for RPi)
• 17 x M2.5 nut (for middle interlayer)
• 16 x M3x5 wide head screw (for 4 hard disks)
• 1 x Long transparent screwdriver
• 1 x Installation instructions
• 4 x Heat sink Kit for Raspberry Pi 4B
• 4 x Heat sink Kit for Raspberry Pi 3B

Note: From 29th Mar 2021 onwards, heatsink sets are NOT included in the packing list.

• Product description
• 4 Layers Cluster Case with Fan Stress Test, tutorial by Cytron Technologies