0.8Amp 5V-26V DC Motor Driver Shield for Arduino (2 Channels)

0.8Amp 5V-26V DC Motor Driver Shield for Arduino (2 Channels)

    • Login to view ProMaker's Insider Price!
    • $10.50
  • Ex Tax: $10.50
    • 10 or more $9.63
    • 30 or more $8.40
  • Cashback: $0.32
  • CytronCash Balance: Login
  • Availability:
    68
  • Product Code: SHIELD-2AMOTOR
  • Warranty Period: 12 months
This DC motor driver shield uses L298P chip which allows control of two 5 - 26V DC brush motors with 0.8Amp continuous current each channel. This shield can be directly stacked onto standard Arduino UNO, Duemilanove, Leonardo, Mega and also CIKU (PIC18F4550).

We have added a few special features onto this shield. Motor power polarity protection, also fast test or manual control buttons for each channel of motor. Adding LSS05 (Auto-calibration line sensor) to Arduino will be easy as this shield comes with the socket for it.

The speed control is achieved through conventional PWM which can be obtained from Arduino's PWM output pin 5 and 6. The enable/disable of motor driver is controlled by Arduino pin 4 and 7, this is labeled as Signed magnitude control. You have option to configure it to become Locked Anti-phase which uses PWM signal to decide direction, speed and also start/stop of motor. The control modes can be configured from jumpers and also program.

The Motor shield can be powered directly from Arduino or from external power source (jumper to select). It is strongly encouraged to use external power supply to power the motor shield.

Specifications and Features:
  • Logic control, 5V from Arduino main board
  • Polarity protection for External motor power input
  • 2 fast test buttons for each motor channel
  • 2 indicator LEDs for each channel
  • bi-directional control of two DC brush motor
  • Motor Driven Voltage:6.5 to 12VDC(VIN Power Supply), 5.0 to 26VDC (External Power Source)
  • 0.8Amp continuous current for each channel (peak 2Amp)
  • Pin 4, 5,6,7 are used to drive two DC motor
  • Support PWM speed control
  • Support  advance speed control
  • Socket for LSS05 - Auto-Calibrating Line Sensor, doing line following robot will be easy
Compatible with:
Documents:
Tutorials:
Introduction Video:

 

Check out this video in Bahasa Malaysia: Part 1 - Tutorial Line Following Robot:

 

[BM] Part 2 - Tutorial of Line Following Robot:

Operating Condition
Motor Channel2
Operating Voltage (VDC)6.5 to 12 (Vin) 5.0 to 26 (External)
Peak Current (A)2 (per channel)
Continuous Current (A)0.8
Operating Modes
Arduino ShieldYes
PWM (Lock-Antiphase and Sign-Magnitude)Yes
UARTNo
AnalogNo
RC Servo SignalNo
Special Protection
Polarity ProtectionYes
Appearance
LEDs IndicatorYes
Test/Manual ButtonYes
Cooling FanNo
Other Features
Extra SocketSocket for LSS05
othersSelectable PWM and DIR pin
if im using the lipo battery 12v how can i connect to the motor shield? if connected, will the arduino uno also get power if i stack on top of it? ( syed alwi, 16/09/2021 )
Hi, you may drop an email to support@cytron.io for further technical assistance. Thanks:)
hi, can this motor driver use to control 2 motors? ( naim, 05/04/2021 )

Hi. Yes, this motor driver can works with 2 units of 5-26V dc brush motor. Thanks :)

I am confused about the specification of this shield.
- the website says that the continuous current it can handle is 0.8A while in the L298P datasheet, it says that the dc operation is 2A.
- the website says that the input voltage range is 5.0 to 26V (ext) while the data sheet says VIH+2.5 to 46V. For Arduino, VIH is 5V, therefore the voltage range is 7.5 to 46V.
Can you please let me know.
I want to buy a bulk of the drivers (40) and I want to drive a motor with a supply of 5V (external) and I am not sure if shield will work.
thanks
( Mostafa Soliman, 20/02/2021 )
Hi, you may drop an email to support@cytron.io so we can help you with further assistance. Thanks :)
Can be use with Arduino due? ( Muhammad Syafiq Ramli, 14/10/2018 )
Hi, yes it can :)
Hi, can this 2A driver motor shield support 2 motors and 2 encoders dagu rover 5? ( Chang, 15/03/2018 )
Hi, this shield supports 2 channel DC motor, but it doesn't have encoder input connector. For further questions, please visit to our technical forum for similar question or post your question there, as this session is only for short inquiry. Thanks.
can i know when it will be restock? ( Ahmad bin Sidik Mat Sidek, 08/03/2018 )
Hi, it will be restocked within 1 week. Thanks.
Can I stack this motor driver to control 6 dc motor? ( Safuan, 21/11/2017 )
Hi, this shield can't be stacked more than one on Arduino board. For further questions, please visit to our technical forum for similar question or post your question there, as this session is only for short inquiry. Thanks.
can this driver control 3 dc motors ? ( fAIRUZ, 17/07/2017 )
Hi, sorry this motor driver only for driving 2 motors only. You might consider using Cytron 4 Channel Motor Driver. Thanks.

Is there any slddrw file for this product? ( Designer, 09/05/2017 )
Hi, sorry we don't have slddrw file for this product. If you have further question, you can go to our technical forum, as this session short inquiry. Thanks.
hi~ can i know how soon it will be restock? ( huifen, 05/05/2017 )
Hi, it will restock in 1 week, thanks for your patience. :)

Ask a question

Note: HTML is not translated!
DescriptionDate AddedSizeAction
Fritzing File14/11/2020N/ADownload
Fritzing Tutorial14/11/2020N/ADownload
  • 4.8 out of 5
                  
Total Reviews (26)
  • 5
    96.15%
  • 4
    0%
  • 3
    0%
  • 2
    0%
  • 1
    3.85%