Shipping charges for both Fedex and DHL surge between 3%-6%. Effective from 4 January 2022.
Best Seller 10Amp 5V-30V DC Motor Driver (2 Channels)

10Amp 5V-30V DC Motor Driver (2 Channels)

    • Login to view ProMaker's Insider Price!
    • $21.18
  • Ex Tax: $21.18
    • 5 or more $20.12
    • 20 or more $19.06
    • 50 or more $16.94
  • Cashback: $0.64
  • CytronCash Balance: Login
  • Availability:
  • Product Code: MDD10A
  • Warranty Period: 12 months

Buy locally from a partner


Note: MDD10A shipped after Jan 2017 is in Rev2.0 which Vmotor supports up to 30VDC.

DC brushed motor is the most commonly used and widely available motor in the market. Getting the motor to rotate is fairly easy, just connect the two terminals to power source and it will start spinning, that's the beauty of DC brushed motor. Yet, if you want to control the speed, direction, activation and automate all these functions, check out this tutorial: 5 easiest ways to control a DC motor. And using motor driver is one of the ways. MDD10A is one of Cytron's motor driver series which offers easy-to-use features and it can drive two independent motors.

MDD10A is the dual-channel version of MD10C which is designed to drive 2 brushed DC motors with a high current of up to 10A continuously. Like MD10C, MDD10A also supports locked-antiphase and sign-magnitude PWM signal. It uses full solid-state components that offers faster response time and eliminates the wear and tear of the mechanical relay.

It can supports Vmotor from 5V to 30VDC. With the presoldered terminals, and on-board manual/test buttons, you can get started even without any microcontroller. Check the video out:

Nonetheless, it is compatible with Arduino or any microcontroller that can output logic signal at 3.3V or 5.0V, and that includes Arduino Zero and Arduino Micro. And not to forget the famous Raspberry Pi SBC too.

Read User's Review:

Which motor is good to be driven by MDD10A? As long as the motor:

  • Is DC Brush motor (Two Terminals)
  • Operating voltage from 5V to 30V
  • Rated Current ≤ 10A
  • Peak Current ≤ 30A

Example of suitable DC brush motor with MDD10A (Not limit to):


  • Bi-directional control for two brushed DC motors.
  • Support motor voltage ranges from 5V to 30VDC (Rev2.0).
  • No Reverse Polarity Protection at Vmotor, please double check the polarity before power up.
  • Maximum current up to 10A continuous and 30A peak (10 seconds) for each channel.
  • Support 3.3V and 5V logic level input (for PWM and DIR), compatible with Arduino and Raspberry Pi.
  • Solid-state components provide faster response time and eliminate the wear and tear of mechanical relay.
  • Fully NMOS H-Bridge for better efficiency and no heat sink is required.
  • Regenerative Braking.
  • Speed control PWM frequency up to 20KHz (output frequancy is same and input frequancy).
  • Support both Locked-Antiphase and Sign-Magnitude PWM operation. ** Note this is not "RC PWM"
  • 2 activation buttons for manual activation or fast test on each channel.
  • Dimension: 84.5mm x 62mm



Packing List:

  • 1 x MDD10A Rev2.0
  • 1 x 2510 PCB connector - 5 ways female
  • 5 x 2510 terminal pin

Check out this review of one of the users, and build a mobile robot with MDD10A and Rasberry Pi:

Operating Condition
Motor Channel2
Operating Voltage (VDC)5 to 25 (Rev 1.0) 5 to 30 (Rev 2.0)
Peak Current (A)30 (10 seconds)
Continuous Current (A)10
Operating Modes
Arduino ShieldNo- can be used with Wire connection
PWM (Lock-Antiphase and Sign-Magnitude)Yes
RC Servo SignalNO
Special Protection
Polarity ProtectionNO
LEDs IndicatorYes
Test/Manual ButtonYes
Cooling FanNO
Other Features
others No heat sink is required
Is the datasheet for this product the same as the datasheet for the MDD10A REV2.0? I can't find its datasheet. ( MM, 30/10/2021 )
Hi, you may drop an email to for further technical assistance. Thanks:)
Hi, is this product certified with the CE or FCC certification? If not, is it because it's not necessary? ( Alberto, 21/07/2021 )
Hi, you may drop an email to for further technical assistance. Thanks:)

I am curious if there is a circuit that can prevent the back electromotive force generated by the DC motor.
( Ion, 27/01/2021 )
Hi, for technical inquiry, you may drop an email to and our technical team will assist on your issue. Thanks :)
Is there a file for custom pcb design for this? For example, I am trying to design a custom PCB board using Autodesk Eagle, or some other EDA software. So is there a file that I can get access for printing my board based on this design. ( MattD, 14/03/2020 )
Hi, you may drop an email to for such inquiry. Thanks :)
hi, can u give me a fritzing library for the MDD10A?? I desperately need it ( Melvin , 22/02/2020 )
Hi, you may refer to the files under 'Documents' on the product page. You may refer to this link too. Thanks :)
Hi,why there is no MDD10A library for Fritzing?if have, i desperately want it
( Melvin , 22/02/2020 )
Hi, you may refer to the files under 'Documents' on the product page. You may refer to this link too. Thanks :)
why MDD10A Cannot Detect Bluetooth Using Arduino ? ( melvin, 11/02/2020 )
Hi, you may drop an email to for technical assistance. Thanks :)
why MDD10A cannot detect bluetooth with arduino ( melvin, 11/02/2020 )
Hi, you may drop an email to for technical assistance. Thanks :)
Hello, does this product have
Overcurrent protection with active current limiting.
Temperature protection.
Undervoltage shutdown.
as have simillar product SHIELD-MDD10?
If not do you have same product with these protections but not with Arduino shield? Thank you
( Radek, 16/10/2019 )
Hi! You may email to for technical assistance. Thanks :)
Is this motor driver can be control using myrio? ( Kesaran , 28/09/2019 )
Hi! We're sorry we do not have the library for this.:)

Ask a question

Note: HTML is not translated!
  • 4.9 out of 5
Total Reviews (97)
  • 5
  • 4
  • 3
  • 2
  • 1

Tags: MDD10A, Dual Channel 10A DC Motor Driver, Robot Controller, DC Motor Driver, SPG30-XX*, SPG50-XX*, 40W DC Brush Motor, IG42 With Encoder (Planetary Gear)*, IG45-XX* dual, channel, 10a, motor, driver, mdd10a