10Amp 5V-30V DC Motor Driver

$13.90
Cashback: $0.42
  • 5 or more $13.21
  • 20 or more $12.51
  • 50 or more $11.82
  • Availability: 1453

    Buy locally from a partner

    Country:
    Description

    DC brushed motor is the most commonly used and widely available motor in the market. Getting the motor to rotate is fairly easy, just connect the two terminals to power source and it will start spinning, that's the beauty of DC brushed motor. Yet, if you want to control the speed, direction, activation and automate all these functions, check out this tutorial: 5 easiest ways to control a DC motor. And a motor driver is one of the ways. MD10C is one of Cytron's motor driver series which offers easy to use features.

    As easy as pressing button, everyone can do it!

     
    *Do check out MD13S which is SMD version of MD10C that have similar spec at lower price!
    MD10C is a newer version of the MD10B(2008) which is designed to drive high current brushed DC motor up to 13Amps continuously.  It offers several enhancements over the MD10B such as support for both locked-antiphase and sign-magnitude PWM signal as well as using full solid state components that result in faster response time and eliminate the wear and tear of the mechanical relay. And with Cytron's motor driver special feature: the on-board manual/test buttons, MD10C is super easy to get started. Check this video to get started without any controller.
     
     
    Nonetheless, it is compatible with Arduino, even Arduino or Raspberry Pi that generate 3.3V logic PWM. Check this video out:
     

    Which motor is good to be driven by MD10C? As long as the motor:

    • DC Brushed motor (Two terminals)
    • Operating voltage from 5V to 30V
    • Rated Current ≤ 13A
    • Peak Current ≤ 30A

    Example of suitable DC brush motor with MD10C (Not limit to):

    Overview of MD10C
     
    Warranty Period: 12 months
    Features
    • Bi-directional control for one Brushed DC motor (Single Channel).
    • Support motor voltage ranges from  5V to 30VDC.
    • No Reverse Polarity Protection at Vmotor, please double check the polarity before power up.
    • Regenerative Braking.
    • Maximum current up to 13A continuous and 30A peak (10 seconds).
    • 3.3V and 5V logic level input, compatible with Arduino and Raspberry Pi.
    • Solid state components provide faster response time and eliminate the wear and tear of mechanical relay.
    • Fully NMOS H-Bridge for better efficiency and no heat sink is required.
    • Speed control PWM frequency up to 20KHz (output frequency is same as input frequency).
    • Support both Locked-Antiphase and Sign-Magnitude PWM operation. **Note that it is not "RC PWM"
    • The new MD10C can be powered from a single power source and NO additonal Vin is required.
    • Dimension: 75mm x 43mm

    Specifications
    Operating Condition
    Compatible input3.3 and 5V
    Motor Channel1
    Operating Voltage (VDC)5 to 25 (Rev 1.0) 5 to 30 (Rev 2.0)
    Peak Current (A)30 (10 seconds)
    Continuous Current (A)13
    Operating Modes
    Arduino ShieldNo- can be used with Wire connection
    PWM (Lock-Antiphase and Sign-Magnitude)Yes
    UARTNO
    AnalogNo
    RC Servo SignalNo
    Special Protection
    Polarity ProtectionNo
    Appearance
    LEDs IndicatorYes
    Test/Manual ButtonYes
    Cooling FanNo
    Packing List
    • 1 x MD10C Rev3.0
    • 1 x 2510 PCB connector - 3 ways female
    • 3 x 2510 terminal pin
    • 4 x plastic spacer(~ 7mm)

     

    Q & A (52)

    Ask a question

    Reviews
    • 4.9 out of 5
                    
    • 5
      92.93%
    • 4
      5.05%
    • 3
      1.01%
    • 2
      1.01%
    • 1
      0%
    Sort By:

    Tags: MD10C, 10Amp DC Motor Driver, Robot Controller, DC Motor Driver, 10amp, motor driver, md10c, motor controller, big motor, DC Motor Drivers