We still deliver orders as usual. Due to current covid-19 situation, all shipment may experience slight delay.
13Amp 6V-30V DC Motor Driver

13Amp 6V-30V DC Motor Driver

  • Brand: Cytron
  • Product Code: MD13S
  • Availability:
    468  need more?
  • Warranty Period: 12 months
  • Login to view ProMaker's Insider Price!
  • $9.90
  • Ex Tax: $9.90
  • Price in reward points: 1584
  • 10 or more $9.13
  • 50 or more $7.92
  • Cashback: $0.30
  • CytronCash Balance: Login

Brushed motor is the most widely used motor because of the ease of operation. Just supply the two terminals DC power supply, the motor will start rotating! Yet, you need a good motor driver to control the speed and direction from microcontroller. You are at the right page, MD13S is one of the easiest to use brushed motor driver.

MD13S has great improvement in current protection which MD10C does not have. With new circuit and design, MD13S is able to limit and support current up to 30A max(10 seconds). And the continuous current is at 13A without heatsink (at room temperature of 25°C).

Not to forget it is GROVE compatible, so get yourself a Grove shield. Oh, did I mention? MD13S is smaller than MD10C :)

Which brush motor is good to be driven by MD13S? As long as the motor:

  • Is DC Brush motor (Two Terminals)
  • Operating voltage from 6V to 30V
  • Rated Current <= 13A
  • Peak Current <= 30A

Example of suitable DC brush motor with MD13S (Not limit to):

Features:

  • Bi-directional control for 1 brushed DC motor
  • Support motor voltage from  6V to 30VDC
  • Maximum current up to 13A continuous and 30A peak (10 seconds)
  • GROVE compatible
  • 3.3V and 5V logic level input.
  • Solid state components provide faster response time and eliminate the wear and tear of mechanical relay
  • Fully NMOS H-Bridge for better efficiency and no heat sink is required
  • Regenerative Braking
  • Speed control PWM frequency up to 20KHz (Actual output frequency is same as input frequency)
  • Support both locked-antiphase and sign-magnitude PWM operation, *NOT RC (Radio Control) PWM
  • SMD compatible
  • RoHS, FCC and CE compliance
  • Dimension: 61mm x 33mm

Documents/Example Code: 

Packing List:

  • 1 x MD13S motor driver board
  • 1 x Green + Black 2-way terminal blocks (Normally Black is for Motor, Green is for Power)
  • 1 x Grove connector (Grove to Grove)

Check out some of the videos by user:

 
Operating Condition
Compatible input3.3 and 5V
Motor Channel1
Operating Voltage (VDC)6 to 30
Peak Current (A)30 (10 seconds)
Continuous Current (A)13
Operating Modes
Arduino ShieldNo- can be used with Wire connection
PWM (Lock-Antiphase and Sign-Magnitude)Yes
UARTNo
AnalogNo
RC Servo SignalNo
Special Protection
Polarity ProtectionNO
Appearance
LEDs IndicatorYes
Test/Manual ButtonYes
Cooling FanNo
Other Features
Extra SocketGroove Compatible
others No heat sink is required

Write a review

Please login or register to review
Hi!
What current is required for PWM and direction inputs? I want to use this driver with PLC, but its outputs are 24V. So i want to use resistors to reduce the voltage.
( Aleksandr, 24/04/2020 )
Hi, you may drop an email to support@cytron.io for technical assistance. Our team will reply to you as soon as possible Thanks :)
What is the manufacturer/series of locking connector used on the control cable so I can design a board that will connect directly to the supplied cable? It doesn't seem to be a JST-PA which is the closest I've found. ( Ian, 15/03/2020 )
Hi, you may drop an email to support@cytron.io for further inquiries. Thanks :)
What is the operating temperature range spec? ( Larry, 28/01/2020 )
HI, we never tested the temperature range. But all components are rated from -40C to 105C except the MOSFET which can go as high as 170C.
Is there anywhere I can tap 5v from this board to power uno board? ( Bard, 05/10/2019 )

Hi! You may consider this item. Thanks :)

Hi
Please could you tell me what the background current draw is to power the board ICs?
Thanks
( AlecM, 17/09/2019 )
Hi, the idle current is dependent on the input voltage.
Vin = 6V, Idle Current = 17mA
Vin = 30V, Idle Current = 43mA
can it do regenerative braking ?
( ayush, 25/07/2019 )
Hi, yes it has a regenerative brake. 
The red wire doesn't do anything, right? I can just remove it? ( ColinC, 24/03/2019 )
Hi, the red wire is not connected. It depends on you to keep it or not :)
I now have four MD13S and I am very happy with them.
You don't happen to have a CAD drawing do you? Step file or Autocad or something?
( ColinC, 24/03/2019 )
Hi, thanks for supporting our product. For this product, we only have eagle cad drawing. You may refer to this link to download. Thanks.
Can you tell me what is the hole spacing please. I have 4 of these on the way and I'd like to get the mounts resdu. ( ColinC, 18/03/2019 )

Hi, you may refer to this photo.


What does the error LED indicate, specifically. ( ColinC, 18/03/2019 )
Hi, the ERR LED Indicator - Error LED Indicator, it will illuminate when fault detected in on board MOSFET driver. 

Ask a question

Note: HTML is not translated!
  • 4.9 out of 5
                  
Total Reviews (20)
  • 5
    95%
  • 4
    0%
  • 3
    5%
  • 2
    0%
  • 1
    0%

Tags: 13A DC motor driver, 10A motor Driver, DC Motor Driver, GROVE, 30A Peak, 13amp, grove compatible, md13s, H-Bridge, big motor, motor controller, robot controller