RFBee 433MHz UART Wireless Module (1km)

  • Brands Cytron Code: RFBEE-433MHZ MPN:
Availability: Discontinued

Buy locally from a partner

This module is compatible with 433MHz RF Transceiver Module (UART)-1km in term of wireless communication. We have come out with XBee form factor which enable user to utilize SKXBee and XBee shield.

This wireless serial port communication module is a new-generation multi-channel embedded wireless data transmission module. Serial transceiver module is a low cost, high performance transparent FSK transceiver with operating frequency at 433 MHz. It features small size, XBee form factor,  high output power, high sensitivity, long transmission distance and high communication data rate with auto setup for communication change and data receiving and transmission control. With UART interface, it is easy to realize the wireless data transmission with only providing the UART data. With XBee from factory, user is welcome to utilize SKXBee or XBee Shield. It is flexible for user to set the UART baud rate, frequency, output power, data rate, frequency deviation, receiving bandwidth parameters. It is the ideal choice for designing wireless data transmission products which can be widely used in wireless data transmission field.

The PCB antenna pedestal ANT2 on the module has been extended out on PCB, it is convenient for user to solder the spring antenna that comes with the module. User can use external antenna of 433MHz frequency band through coaxial cable, the connector is still on the module, bottom of the module. User could select one of these antennas according to requirements.

With the XBee form factor, we have simplify the process to change between command and transparent mode, with a slide switch. With RFBee, insert in SKXBee, push the slide switch to "AT" and you can start sending AT command and further configure it. Push the slide switch back to "TRANS", and it act as transparent UART transceiver. 

There is MCU on the module, and user must send data in UART protocol to utilize the module. In transparent transmission mode, the module act like normal receiving and sending serial port data, so it is convenient to use. The module adopts multiple serial port transparent transmission modes, and user could select them by AT command according to user's requirements. The average working current of three modes FU1, FU2 and FU3 in idle state is 80µa, 3.5mA and 22mA respectively, and the maximum working current is 100mA (in transmitting state). Not to forget, you will need 1 pair of same RFBee to get wireless communication.

*This RFBee is not compatible with 434MHz wireless UART module (100m) or RFBee 434MHz UART Wireless module

  • Long-distance wireless transmission (500m in open space/baud rate 5,000bps in the air)
  • Working frequency range (433.4-473.0MHz, up to 100 communication channels)
  • Maximum 100mW (20dBm) transmitting power (8 sets of power can be set)
  • Three working modes, adapting to different application situations
  • Built-in MCU, performing communication with external device through serial port
  • Working frequency: 433MHz
  • Supply voltage: 3.3V
  • Communication distance: 1 meter to 100 meters indoor
  • Communication distance: up to 500 meters (line of sight) outdoor
  • Serial baud rate: 1.2Kbps to 115.2Kbps (default 9.6Kbps)
  • Receiving sensitivity: -117dBm to -100dBm
  • Transmit power: -1dBm to 20dBm
  • Interface protocol: UART/TTL
  • Operating temperature: -40℃ to +85℃
  • Dimensions: 24.5 x 32.5 x 8.5 mm


Warranty Period: 12 months
RFBee 433MHz User's Manual
Schematic diagram
Q & A (6)

Ask a question

No Review Found

Tags: RFBEE-433MHZ, RFBee 433MHz UART Wireless Module (1km), Wireless Devices, RF Module, SKXBEE-BOARD, SHIELD-XBEE, BB-XBEE rfbee, 433mhz, uart, wireless, module, rfbee-433mhz