Setup 3.5-Inch TFT on Raspberry Pi 5

Setup 3.5-Inch TFT on Raspberry Pi 5

A guide on the setup and installation for 3.5-Inch 480x320 TFT 50FPS display on Raspberry Pi 5...
Raspberry Pi 5 RTC Battery

Raspberry Pi 5 RTC Battery

Guide for the installation and basic usage of RTC battery on Raspberry Pi 5..
Make Turntable using MD10-POT Motor Driver

Make Turntable using MD10-POT Motor Driver

This tutorial is application of MD10POT motor driver that can be use directly from the board without programming. The turntable is produce using 3D Printing method...
Retrofitting a 1MW Solar Farm for Efficiency with IRIV PiControl

Retrofitting a 1MW Solar Farm for Efficiency with IRIV PiControl

Reviving a 1 MW Solar Farm with an IRIV PiControl, getting data from all 16 inverters, restrunning the data, and sending it to the cloud...
Setup 5 inch TFT Screen for Raspberry Pi 4

Setup 5 inch TFT Screen for Raspberry Pi 4

A guide on how to properly setup 5inch TFT Screen onto Raspberry Pi 4B and 5..
Build 1KG RC Sumo Robot using MDDRC10

Build 1KG RC Sumo Robot using MDDRC10

This is a RC Sumo Robot based on MDDRC10 Motor Driver. The sizes are 15cm(L) x 15cm(W) with below 1kg (weight). The spec is for 1kg Sumo Robot Competition..
A fatal esptool.py error occurred: Cannot configure port!

A fatal esptool.py error occurred: Cannot configure port!

This tutorial is short summarizes on common issues with ESP8266 or ESP32 Arduino base boards. It usually happens while tinkering with Arduino IDE and ESP chips...
Raspberry Pi Imager: Updating Bootloader On A Raspberry Pi

Raspberry Pi Imager: Updating Bootloader On A Raspberry Pi

Keeping your Raspberry Pi's firmware up-to-date is crucial for accessing new features, improvements, and bug fixes...
Object Detection with Edge Impulse Using Mobile Phone

Object Detection with Edge Impulse Using Mobile Phone

Edge Impulse enables the creation of an object detection project on a mobile device. Utilising the smartphone's camera, this project gathers data and constructs a machine learning model...
Introduction on Programming 1KG Autonomous Sumo Robot

Introduction on Programming 1KG Autonomous Sumo Robot

This is tutorial for programming Autonomous Sumo Robot using Arduino IDE. We will show you how to use Arduino IDE and how to write a coding for the sumo robot..
IRIV PiControl - Quick Start Guide With Built-in Dashboard

IRIV PiControl - Quick Start Guide With Built-in Dashboard

This concise guide covers powering up, connecting to the demo network, and navigating the monitoring dashboard...
Edge Impulse with Raspberry Pi Pico Application Using Ultrasonic Sensor

Edge Impulse with Raspberry Pi Pico Application Using Ultrasonic Sensor

Edge Impulse now supports devices with the RP2040 chip. The project uses the Raspberry Pi Pico with the RP2040 chip to create an ultrasonic ranger for distance measurement...
1KG Autonomous Sumo Robot Starter Kit User Guide

1KG Autonomous Sumo Robot Starter Kit User Guide

This is an upgraded version of the previous 500g mini-sumo robot. This version comes with a 1kg sumo robot specification which is less than 1kg (weight) and less than 15cmx15cm (size)..
Installing CH340 Driver on Mac OS

Installing CH340 Driver on Mac OS

Basic guide on how to install CH340 on Macbook or Mac Os related device to be used with Maker Uno..
Edge Impulse with Raspberry Pi Pico Application Using ADC Light Sensor

Edge Impulse with Raspberry Pi Pico Application Using ADC Light Sensor

Edge Impulse has the ability to interface with the Raspberry Pi Pico device, equipped with the RP2040 chip. In this project, data is gathered using the light sensor to measure light intensity...